2001 Ford Mustang GT Drag Racer

Flaky buyer never showed up or communicated, so this post is back up.

Please read the entire post before inquiring!!! I will not reply to “Is it still available”!! All inquiries must be in ENGLISH!

If this post is still up, then the car is still available. DO NOT ASK ME IF THE CAR IS STILL AVAILABLE OR WHAT MY LOWEST PRICE IS. THOSE MESSAGES WILL BE IMMEDIATELY DELETED AND BLOCKED!! Post will be promptly removed once sold!

THIS IS NOT A PART OUT!!

2001 Ford Mustang GT currently set up for drag racing only (bracket car). Only basic interior for driver only. Currently the car weighs just over 3k lbs. I bought the car with a branded title, since it only needed to be functional and go straight, 1/4 mile at a time.

Due to my work schedule, she has been sitting for a couple years, so she’s in rough shape and will need some cleaning and freshening up. Photo are of her when she was running good and competing on a weekly basis.

Free delivery within 120 miles or 2 hours of Vancouver WA.

Check out my facebook page for videos and additional photos.
https://www.facebook.com/profile.php?id=+1 (954) 487-7722409

Best light - .000 (perfect Light)
Best 60’ – 1.878
Best 330’ – 5.481
Best 1/8 Mile pass – 8.686
Best 1/8 MPH – 81.73
Best 1000’ – 11.470
Best 1/4 Mile pass - 13.642
Best 1/4 MPH – 102.49

Car has 115k miles on it.
• Stock 4.6 long block
• Stock automatic transmission
• Pro built ’03-’04 Cobra Solid Axle SWAP (This is the rear end that Cobra owners would use if doing a solid axle swap) () – Only 65 passes on the rear end
o TIG WELDED tubes all of the seams for increased structural strength
o It has been Powder coated with a matte black finish
o 2003 2004 Mustang Cobra 31 spline limited slip differential with Carbon Fiber Clutch pack.
o NEW Ford Racing 4.30:1 Gears
o New Moser 31 spline axles
o NEW Ford racing 11.65 inch "Cobra" brake kit 2300m
o New Ford Racing Aluminum housing cover and stud girdle
o New pinion flange
o New brake lines
o New E-brake cables
o New upper control arm bushings
o ABS ring delete
o Extended wheel studs for drag racing
o ALL NEW OEM BEARINGS AND SEALS
o MM Stainless Brake Hose Kit, 1999/­04 IRS Cobra
• NHRA Approved Driveshaft Safety Loop
• Maximum Motorsports Solid Motor Mounts
• Plug-in MIL Eliminators (96-04 All)
• Pace Setter Longtube Exhaust Header 70-3230
• Flowmaster Super 10 series single chamber racing mufflers
• Cobra Front Fascia Conversion Kit - Unpainted (99-04 All)
• Cobra fog lights
• Raxiom Icon LED Tail Lights and Sequential Tail Light Kit
• Bama Livewire TS+ Tuner
• Ford Performance A/C Delete
• Corbeau 3-Inch 5-Point Camlock Harness Belt
• Corbeau Seat Belt Harness Bar
• Procar Sportsman Pro Reclining Seat & Bracket
• SR Performance Rear Upper and Lower Control Arms; Red
• Maximum Motorsports Full Length Weld In Subframe Connectors - Bare (Not Installed-Still In Box)
• BBK Cold Air Intake
• BBK 78mm Throttle Intake
• SR Performance EGR Cover
• Aeromotive 15+1 (954) 487-7722 Ford 4.6 L Fuel Rail Pressure Sensor Adapter Log (-08 AN inlet/outlet)
• Edelbrock Fuel Rails
• Custom Stainless Steel braided fuel line
• Edelbrock Victor Jr Ford 4.6L Modular Intake Manifold EFI
• MMR 4.6 2V SOHC Edelbrock intake adapter plate
• IAC delete plate
• 4” Fiberglass Cowl Hood
• SVE Drag Wheels
o Front - SVE-1+1 (954) 487-7722-13 SVE Drag Wheel 17x4.5 Chrome) 19.3LBS
o 26x6x17 Mickey Thompson Sportsman S/R Front Runner Tires
o Rear - SVE-1+1 (954) 487-7722-04 SVE Drag Wheel 15X10 Chrome) 19.2LBS
o Hoosier 28.0/10 R15 Drag Racing Slicks
• Ford Racing Lowering Springs
• Saleen style rear spoiler
• New battery

Asking
Local cash sale. No shipping.

Possible trades for the following:
• 24’ or larger enclosed car trailer with ramp load and driver’s side escape door (gooseneck or 5th wheel ok).
o No leaks
o No body damage

• 19’-22’ Open bow boat with trailer (V6 or small block V8 powered)
o No salt water
o Must run and drive
o No mechanical issues
o No leaks
o Must be able to hit the water now

10/2 update - I just got the MSD 6011 Modular Ignition Controller (Not installed yet) for carbureted conversion. The more parts I acquire for the carb conversion, the more the price will go up.